カガブログ新館「マカオ」|卡加部落格新館「澳門」|Novo KAGABLOG「Macau」|New KAGABLOG「Macao」

前日、X10 miniをGingerbreadのカスタムＲＯＭを入れ、今度はオーバークロックのモジュールもやってみた。

もともと、X8の開発だったが、X10 miniにもX10 mini proにも導入され、さっそくそれをいれてやってみた。

改造する前にはSetCPUでどうしても600 Mhz以上の設定できず、改造したら、800 Mhz以上くらいのOCもあるが、そうするとすぐにフリーズになった。ｗ

安定性を守りながらOCにすれば、一般的なコメントによると、710 Mhzまたその前後にしてほうがいいとされて、僕は710 Mzhにしてから、RockPlayerで普通のrmvbを再生してみたら、なんとなくスムーズに再生できたから、今までＸ10 miniとRockplayer+RMVBの無縁を乗り越えて、本当に不思議だった。

 [Module] X8Overclock | v004 – Multiple freq | X8 | X10 mini | X10 mini pro | 11-04-11 – xda-developers

 

 

 

Release history

 

• April 11. v004. Default to 691MHz. Multiple frequencies are available for SetCPU: from 614MHz to 826MHz. You can now change frequencies with SetCPU – much like with custom kernels! You can even SetCPU freq at boot.
• April 07. v003. Compatible with SetCPU. Easier for code maintenance.
• April 06. v002 for mini pro. x8oc module for x10 mini pro released! Be warned: I didn’t have your x10mini pro hardware so I didn’t test it throughoutly.
• April 06. v002 for mini. x8oc module for x10 mini released! Be warned: I didn’t have your x10mini hardware so I didn’t test it throughoutly. 710MHz was reported not too stable. A lower freq is more stable.
• April 06. v002. Experimental! It maybe very unstable! Undervoltage for all frequencies except the max freq (Reduced voltages for 128MHz, 245MHz, 320MHz, 480MHz). This can potentially save battery. I need test results for saving battery from you guys 
• April 05. v001. Default to 710MHz.

Requirements:
– Rooted
– Baseband x15
– xRecovery (for automatic installtation)
– Dare!

Installation:
a. Manual installation : it will be better if you can do this way.
– Download appropriate x8oc-vXXX.zip (for X8), or x8oc-vXXX-x10m.zip (for X10 mini), or x8oc-vXXX-x10mp.zip (for x10 mini pro) below, unzip
– Remount /system as rw
– Push x8oc.ko in to /system/lib/modules
– Edit /system/etc/hw_config.sh, add one line at the beginning

Code:

insmod /system/lib/modules/x8oc.ko # x8 overclock

For people who want to set specific freq at boot, write the following instead of the code above:

Code:

# x8 overclock
insmod /system/lib/modules/x8oc.ko 
sleep 2
echo xAB > /proc/x8oc

Where AB is your desired code for that frequency. Test the frequency carefully before applying it at boot!
(you can edit hw_config.sh by pulling it to your PC, edit, and push it back)
– Reboot your phone

b. Automatic installation : much like x8gesture, I will have to prepare update.zip for each ROM. I’m pretty busy now, so be patient.

 

之前,安裝了Gingerbread的定制ROM到X10 mini,今次試吓超頻一吓.

原為X8之開發的,不過都有X10 mini及X10 mini pro導入之版本,所以試一吓佢.

改造之前,用SetCPU點都係調唔到600 Mhz以上的設定,改造之後可有調至800 Mhz以上的超頻,不過一調就即死機了.w

要保持穩定性去超頻的話,依一般的評論話,調為710 Mhz左右咁上吓係最好的,而我調為710 Mzh之後,試用RockPlayer去播啲普通rmvb,總算播得幾順吓,超越咗至今X10 mini與Rockplayer+RMVB之無綠的境界,真係好不可思議啊.

 [Module] X8Overclock | v004 – Multiple freq | X8 | X10 mini | X10 mini pro | 11-04-11 – xda-developers

 

 

 

Release history

 

• April 11. v004. Default to 691MHz. Multiple frequencies are available for SetCPU: from 614MHz to 826MHz. You can now change frequencies with SetCPU – much like with custom kernels! You can even SetCPU freq at boot.
• April 07. v003. Compatible with SetCPU. Easier for code maintenance.
• April 06. v002 for mini pro. x8oc module for x10 mini pro released! Be warned: I didn’t have your x10mini pro hardware so I didn’t test it throughoutly.
• April 06. v002 for mini. x8oc module for x10 mini released! Be warned: I didn’t have your x10mini hardware so I didn’t test it throughoutly. 710MHz was reported not too stable. A lower freq is more stable.
• April 06. v002. Experimental! It maybe very unstable! Undervoltage for all frequencies except the max freq (Reduced voltages for 128MHz, 245MHz, 320MHz, 480MHz). This can potentially save battery. I need test results for saving battery from you guys 
• April 05. v001. Default to 710MHz.

Requirements:
– Rooted
– Baseband x15
– xRecovery (for automatic installtation)
– Dare!

Installation:
a. Manual installation : it will be better if you can do this way.
– Download appropriate x8oc-vXXX.zip (for X8), or x8oc-vXXX-x10m.zip (for X10 mini), or x8oc-vXXX-x10mp.zip (for x10 mini pro) below, unzip
– Remount /system as rw
– Push x8oc.ko in to /system/lib/modules
– Edit /system/etc/hw_config.sh, add one line at the beginning

Code:

insmod /system/lib/modules/x8oc.ko # x8 overclock

For people who want to set specific freq at boot, write the following instead of the code above:

Code:

# x8 overclock
insmod /system/lib/modules/x8oc.ko 
sleep 2
echo xAB > /proc/x8oc

Where AB is your desired code for that frequency. Test the frequency carefully before applying it at boot!
(you can edit hw_config.sh by pulling it to your PC, edit, and push it back)
– Reboot your phone

b. Automatic installation : much like x8gesture, I will have to prepare update.zip for each ROM. I’m pretty busy now, so be patient.